Skip to content
Rulebook
Indianapolis International Airport seen from the FAA control tower: terminal, runways and parking lots

Drone airspace classes: can drone pilots fly in controlled airspace?

A drone needs FAA authorization in four places: Class B, Class C, Class D and the surface area of Class E designated for an airport.

Checked against the FAA's own documents, November 14, 2026.Part 107 and flying for fun, kept apart

Areas that need an authorization
4
Drone limit above the ground
400ft
Class E transition areas from
700ft AGL
Class D, above the airport
2,500ft
Class A starts at
18,000ft MSL

Which airspace class needs authorization for drone pilots?

Four areas need an authorization before a drone flies in them, for Part 107 pilots and recreational flyers alike: Class B, Class C, Class D, and the surface area of Class E designated for an airport.

  • The four areas

    The same four apply to Part 107 pilots and to recreational flyers; the rest of Class E and all of Class G need none.

    Ask first
  • Class A

    Class A starts at 18,000 feet MSL, far above any drone flight.

    Out of reach
  • The rest

    The rest of Class E, and all of Class G, need no authorization.

    No ask
  • “Controlled airspace”

    “Controlled airspace” is a wider term than those four: 14 CFR 1.1 uses it for Class A, B, C, D and E. So an app that shows controlled airspace over your spot does not always mean you need to ask; what decides is whether the spot is in Class B, C or D or in a Class E surface area.

    Check the class

Part 107 does not apply to a recreational flight under 49 U.S.C. 44809 (14 CFR 107.1(b)(2)), so the two sets of rules stay separate on this page.

The 7 airspace classes, by what a drone needs
Authorization needed, for Part 107 pilots and recreational flyers alike Class B; Class C; Class D; Class E surface area (to the surface, designated for an airport).
4
No authorization needed Class E, all other (transition areas, airways, from 14,500 ft MSL); Class G (uncontrolled).
2
Not named in either rule, and far above any drone flight Class A.
1

Find the class at your spot

Check your spot in Can I fly here? before you fly.

Can I fly here?

The rule in its own words: 14 CFR 107.41 and 49 U.S.C. 44809(a)(5)

The regulation and the statute name the same four areas; Part 107 pilots get the permission from air traffic control, recreational flyers from the FAA.

  • Part 107 pilots

    Prior authorization from Air Traffic Control (ATC) before a flight in Class B, C or D airspace or a Class E surface area.

    Ask ATC
    The exact rule
    No person may operate a small unmanned aircraft in Class B, Class C, or Class D airspace or within the lateral boundaries of the surface area of Class E airspace designated for an airport unless that person has prior authorization from Air Traffic Control (ATC). 14 CFR 107.41, Operation in certain airspace (eCFR)

    What it means: the section names four areas and no others. Class E counts only where it is the surface area designated for an airport.

  • Recreational flyers

    Prior authorization from the Administrator or designee, that is the FAA, in the same four areas.

    Ask the FAA
    The exact rule
    In Class B, Class C, or Class D airspace or within the lateral boundaries of the surface area of Class E airspace designated for an airport, the operator obtains prior authorization from the Administrator or designee before operating and complies with all airspace restrictions and prohibitions. 49 U.S.C. 44809(a)(5), Exception for limited recreational operations of unmanned aircraft

    What it means: the same four areas, with the permission coming from the FAA, and every airspace restriction, such as a TFR, still applies.

  • The FAA fact sheet

    The FAA's Part 107 fact sheet of July 6, 2026 words it more broadly: “Operations in Class B, C, D and E airspace need ATC authorization.” The regulation and the statute name only the surface area of Class E designated for an airport, and this page follows them.

    Broader words
  • Waivers

    Section 107.41 can be waived, since it is on the list in 14 CFR 107.205.

    Waivable
  • Part 108

    A proposed rule for flights beyond visual line of sight (part 108, published August 7, 2025) would rewrite 107.41; it is proposed, not adopted, as of November 14, 2026.

    Proposed
Under Part 107, the authorization comes from air traffic control.

How you ask

Part 107 pilots ask air traffic control and recreational flyers ask the FAA, both through a LAANC app or FAADroneZone.

LAANC guide

Airspace classification at a glance

Around an airport, Class B, C and D and the Class E surface area reach down to the ground; away from them, a drone flies in Class G below the Class E floor.

Class A: from 18,000 ft MSL Not to scale Authorization needed Class E from 700 ft AGL Class D Class E surface Class C Class B wedding cake Not Class B 400 ft: the drone limit Class G: no authorization Class A Not to scale Authorization needed Class E D E C B 400 ft Class G
Not to scale. Shaded: the four areas where a drone needs an authorization. The dashed line is 400 feet above the ground; below the Class E floor, often 700 or 1,200 feet AGL, is Class G.

The FAA divides the national airspace system into regulatory areas (Class A, B, C, D and E, restricted and prohibited areas) and nonregulatory areas (military operations, warning, alert, controlled firing and national security areas), and into four types: controlled, uncontrolled, special use and other airspace (AIM 3-1-1). Where designations overlap, the more restrictive one applies: A over B, B over C, C over D, D over E and E over G (AIM 3-1-3). The areas around each airport are set in FAA Order JO 7400.11M, incorporated into 14 CFR part 71 through September 15, 2027.

On the knowledge test

Airspace is on the Part 107 knowledge test: the FAA's test standards cover Class B, C, D, E and G, special use airspace and other areas such as TFRs. Try the questions in our Part 107 practice test.

The airspace classes, A to G
ClassUsual shape and heightsOn the sectional chartPart 107Recreational flyersRule
Class AFrom 18,000 ft MSL up to and including FL 600, over the 48 states and Alaska and the waters within 12 NM of the coast; all flights under IFR unless otherwise authorized.Not shown: visual charts do not depict Class A.Not named in 107.41. It starts at 18,000 ft MSL, far above the Part 107 limit of 400 ft above ground (107.51(b)).Not named in 44809(a)(5). Far above recreational flying heights.14 CFR 71.31 and 71.33 (designation); 14 CFR 107.51(b).
Class BIndividually tailored: a surface area and two or more layers, some resembling upside-down wedding cakes, up to 10,000 ft MSL. Under a layer whose floor is above you, you are not in Class B.Sector ceilings and floors in solid blue figures with the last two zeros omitted; a floor marked + means operations at and below it are outside Class B; legend graphic: solid blue boundary.Yes: prior authorization from air traffic control (14 CFR 107.41).Yes: prior authorization from the FAA (49 U.S.C. 44809(a)(5)).14 CFR 107.41; 49 U.S.C. 44809(a)(5); 14 CFR 71.41 (designation).
Class CUsually a 5 NM radius core surface area from the surface to 4,000 ft above the airport and a 10 NM radius shelf from no lower than 1,200 ft up to 4,000 ft above the airport.Sector ceilings and floors in solid magenta figures with the last two zeros eliminated; a ceiling of T means up to the floor of the overlying Class B; part-time Class C shown by a note; legend: solid magenta line.Yes: prior authorization from air traffic control (14 CFR 107.41).Yes: prior authorization from the FAA (49 U.S.C. 44809(a)(5)).14 CFR 107.41; 49 U.S.C. 44809(a)(5); 14 CFR 71.51 (designation).
Class DIndividually tailored. Full-time or part-time; part-time hours are in the Chart Supplement, and at other times the area may revert to a Class E surface area or to Class G. Arrival extensions of 2 miles or less stay Class D; if any is longer than 2 miles, all extensions are Class E.Blue dashed line (AIM: blue segmented lines); ceiling in a box, a minus before the figure means from the surface to, but not including, that altitude; part-time Class D shown by a note.Yes: prior authorization from air traffic control (14 CFR 107.41). When a part-time Class D reverts to a Class E surface area, 107.41 still applies; when it reverts to Class G, it does not.Yes: prior authorization from the FAA (49 U.S.C. 44809(a)(5)). The same holds when a part-time Class D reverts.14 CFR 107.41; 49 U.S.C. 44809(a)(5); 14 CFR 71.61 (designation).
Class E surface area (to the surface, designated for an airport)Around airports with weather reporting and radio coverage down to the runway; also used for the hours a part-time Class C or D tower is closed. Extensions to Class B, C, D and E surface areas begin at the surface and reach the overlying controlled airspace.Magenta dashed line; legend: airspace beginning at the surface designated for airports and extension areas; part-time Class E surface shown by a note.Yes: prior authorization from air traffic control (14 CFR 107.41). Extensions: the AIM says arrival extensions become part of the surface area; neither the rule nor the AIM says whether a drone needs authorization inside one. Check the UAS Facility Map.Yes: prior authorization from the FAA (49 U.S.C. 44809(a)(5)). Extensions: as for Part 107.14 CFR 107.41; 49 U.S.C. 44809(a)(5); 14 CFR 71.71(b) (designation).
Class E, all other (transition areas, airways, from 14,500 ft MSL)Transition areas start at 700 ft AGL or 1,200 ft AGL and stay in effect regardless of airport hours; Federal airways from 1,200 ft AGL; elsewhere Class E starts at 14,500 ft MSL. Below these floors the airspace is usually Class G.700 ft floors: magenta vignette; floors other than 700 ft that abut Class G: blue vignette; Class E exists at 1,200 ft AGL unless designated otherwise.No. 107.41 names only the surface area of Class E designated for an airport.No. 44809(a)(5) names only the surface area.14 CFR 107.41; 49 U.S.C. 44809(a)(5); 14 CFR 71.71(a) and (c) to (f) (designation).
Class G (uncontrolled)From the surface up to the floor of the overlying Class E, often 700 ft or 1,200 ft AGL; in places up to 14,500 ft MSL.No boundary line of its own; Class G within the U.S. extends up to 14,500 ft MSL; its edges with controlled airspace are the vignettes (blue vignette where floors other than 700 ft abut Class G).No authorization. Part 107 limit: 400 ft above ground, or within 400 ft of a structure (107.51(b)).No authorization (AC 91-57D 2.2.5.1). Fly from the surface to not more than 400 ft above ground (44809(a)(6)).14 CFR 107.51(b); 49 U.S.C. 44809(a)(6); AC 91-57D 2.2.5.1.

7 rows, the airspace classes from A to G with Class E in its two kinds, from the AIM, the FAA Chart Users' Guide, 14 CFR and 49 U.S.C., read November 13, 2026.

Class A airspace

Out of a drone's reach: Class A starts at 18,000 feet MSL, and neither rule names it.

  • Where

    Class A runs generally from 18,000 feet MSL up to and including FL 600, and unless otherwise authorized every flight in it is under instrument flight rules (IFR) (AIM 3-2-2).

  • On the chart

    Visual charts do not show it.

  • Drones

    Part 107 keeps a drone at or below 400 feet above the ground, or within 400 feet of a structure (14 CFR 107.51(b)), so Class A is far out of reach, and neither rule names it.

    Out of reach

How high a drone flies

Our guide to the 400-foot limit covers flights near a structure and the recreational rule.

Class B airspace

Class B surrounds the nation's busiest airports, and a drone needs an authorization in it, though not under a layer whose floor is above you.

  • Where

    Class B surrounds the nation's busiest airports in terms of IFR operations or passenger enplanements, generally from the surface to 10,000 feet MSL.

  • Shape

    Each one is individually tailored: a surface area and two or more layers, some like upside-down wedding cakes (AIM 3-2-3).

  • Going in

    A crewed aircraft needs an ATC clearance to enter it in any weather; a drone needs an authorization.

    Authorization
  • On the chart

    On sectional and terminal area charts, the boundary is a solid blue line and each sector's ceiling and floor are in solid blue figures with the last two zeros left off.

  • Under a layer

    A floor marked + means flight at and below it is outside Class B. So under a layer whose floor is above you, you are not in Class B, and the airspace below that layer decides whether you need to ask.

    Class below decides

Under the shelf

In the drawing above, the drone under the Class B layer is not in Class B: the class beneath the layer decides.

See the drawing

Class C airspace

Class C surrounds busy airports with a control tower and radar approach control, generally from the surface to 4,000 feet above the airport.

  • Where

    Class C surrounds airports that have an operational control tower, are served by a radar approach control and have a certain number of IFR operations or passenger enplanements. It runs generally from the surface to 4,000 feet above the airport elevation, charted in MSL (AIM 3-2-4).

  • Core and shelf

    It usually has a core of 5 nautical miles (NM) radius from the surface and a shelf out to 10 NM from no lower than 1,200 feet, both up to 4,000 feet above the airport.

    Authorization
  • Outer Area

    A procedural Outer Area, normally 20 NM out, is not charted and is not Class C itself.

    Not Class C
  • On the chart

    On the chart: a solid magenta line, with ceilings and floors in solid magenta figures, the last two zeros left off. A ceiling of “T” means up to the floor of the Class B above, and a note marks a part-time Class C.

5 NM and 10 NM

The usual core and shelf. Under the shelf, below its floor, you are outside Class C.

Class D airspace and part-time towers

Class D generally extends from the surface to 2,500 feet above the airport elevation, around airports that have an operational control tower (AIM 3-2-5).

The height is above the airport, though the chart prints it in MSL: an airport at 1,000 feet has a Class D ceiling near 3,500 feet MSL. Each Class D is individually tailored, so its size comes from the chart, not from a set radius. The chart draws it as a blue dashed line, with the ceiling in a box; a minus sign before the figure means from the surface up to, but not including, that altitude.

  • Part-time towers

    A Class D surface area can be full-time or part-time, and the hours are in the Chart Supplement. At other times it becomes a Class E surface area, which still needs an authorization, or Class G, which does not; the airport listing says which, for example “other times CLASS E” or “other times CLASS G”. A Class G surface area reaches up to, but not including, the controlled airspace above, normally Class E from 700 or 1,200 feet AGL.

    Check the hours
  • In LAANC apps

    The FAA's rules for app makers (LAANC USS Performance Rules v9.0, 3.4.3) have the apps apply each airspace volume's published schedule; when no controlled volume is active, the spot is Class G and no authorization is required.

    Schedule applied
  • Extensions

    Arrival extensions of 2 miles or less stay part of the Class D surface area; if any one is longer than 2 miles, all of them are Class E. Extensions follow the surface area's hours.

    Authorization

An airport at 1,000 feet

Its Class D ceiling sits near 3,500 feet MSL on the chart: 2,500 feet above the airport.

Types of Class E airspace: which need authorization

Only one kind needs a drone authorization: the surface area designated for an airport.

Class E is controlled airspace designated to serve a variety of terminal or en route purposes (AIM 3-2-6). Only one kind needs a drone authorization, and 14 CFR part 71 keeps it apart from the rest: Class E surface areas “for an airport” in 71.71(b), and areas that start at 700 or 1,200 feet above the surface in 71.71(c).

  • Surface area

    Surface area designated for an airport: authorization needed. It is designated where a control tower is not in operation and runs from the surface to a set altitude or to the controlled airspace above. The airport needs weather reporting and radio contact down to the runway, and a Class E surface area may also cover the hours a part-time Class C or D tower is closed. On the chart: a magenta dashed line. Its shape comes from the chart and the UAS Facility Map, which exists for every Class E surface area, not from a set radius.

    Authorization
  • Extensions

    Extensions to a surface area: not settled. They begin at the surface, and the AIM says arrival extensions “become part of the surface area”. Neither the rule nor the AIM says whether a drone needs an authorization inside one. Check the spot on the FAA's UAS Facility Map or in Can I fly here? before you fly.

    Not settled
  • From 700 or 1,200 ft

    Transition areas from 700 or 1,200 feet AGL: no authorization. They serve airports with instrument procedures and stay in effect whatever the airport's hours. The AIM warns not to confuse them with surface areas or surface area extensions. A drone at 400 feet or lower under a 700-foot floor is below that floor, usually in Class G.

    No ask
  • Airways

    Federal airways: no authorization. Class E from 1,200 feet AGL up to, but not including, 18,000 feet MSL unless otherwise specified.

    No ask
  • From 14,500 ft MSL

    From 14,500 feet MSL: no authorization. Elsewhere Class E starts at 14,500 feet MSL, excluding the airspace less than 1,500 feet above the surface.

    No ask

Low clouds over a surface area

One limit appears only in the FAA's rules for LAANC suppliers (LAANC USS Performance Rules v9.0, 3.4.6): a LAANC approval is not valid in Class E surface area airspace when the weather ceiling is below 1,000 feet, and the app must tell you when that applies to your flight. The reason they give is special VFR, under which crewed aircraft may fly low beneath such a ceiling (AIM 3-1-4). More on LAANC.

Class E and G airspace away from airports: where you can fly without authorization

Neither rule asks for an authorization in Class G airspace or in Class E away from the airport surface area.

Class G, uncontrolled airspace, is the airspace not designated as Class A, B, C, D or E (AIM 3-3-1). It runs from the surface up to the floor of the Class E above, often 700 or 1,200 feet AGL, and in places up to 14,500 feet MSL.

  • Part 107 pilots

    Up to 400 feet above the ground, or higher only within 400 feet of a structure and not more than 400 feet above its top (14 CFR 107.51(b)).

    No ask
  • Recreational flyers

    In Class G, from the surface to not more than 400 feet above ground level (49 U.S.C. 44809(a)(6)), and FAA Advisory Circular 91-57D says no authorization is needed there. The statute sets that number for Class G only.

    No ask
  • Airports without a tower

    In uncontrolled airspace: the FAA says prior authorization is not required under 400 feet, but keep clear of traffic patterns and takeoff and landing areas.

    Keep clear
  • Other limits

    No authorization does not mean no limits: temporary flight restrictions, special use airspace and national security restrictions still apply, as the next section shows.

    Still apply
Class G: no authorization, and 400 feet above the ground is the top.

Areas that are not airspace classes but still stop a flight

These sit on top of the classes. A LAANC authorization does not lift any of them, and the FAA does not check 99.7 restrictions when it processes one.

No-go

Prohibited areas

Flight is prohibited there, for security or the national welfare. Only the using agency can authorize a flight; LAANC does not.

Ask

Restricted areas

Unusual, often invisible hazards to aircraft. Advance permission comes from the using or controlling agency named on the chart; LAANC does not grant it.

No-go

Temporary flight restrictions

A type of NOTAM, over a hazard, a special event or a general warning. LAANC apps show them but do not authorize flight in them.

No-go

Washington, DC

Inside the inner 15-mile ring, no drone flight without specific FAA authorization. Between 15 and 30 miles, flights follow the usual rules and the DC NOTAM.

No-go

National security sites

Drones are prohibited over designated national security sensitive facilities, from the ground up to 400 feet above ground level: the red polygons on the FAA UAS Data Delivery System map.

Avoid

National Security Areas

Pilots are asked to avoid them, and flight in one is prohibited only when a 99.7 NOTAM says so. On the chart: a broken magenta line.

No-go

Stadiums

Drone flight is prohibited within 3 nautical miles of a stadium from one hour before to one hour after the scheduled time of MLB, NFL, NCAA Division One football, NASCAR Sprint Cup, Indy Car and Champ Series events.

No-go

National parks

The National Park Service uses 36 CFR 1.5 to prohibit launching, landing or operating drones on park lands and waters; FAA airspace rules are unchanged. More in drones in national parks.

Check your spot

Look up the place you plan to fly from before you go.

Can I fly here?
Each area in detail: the chart, the rule, the permission
Areas that are not classes
AreaWhat it isOn the chartPart 107Recreational flyersPermissionRule
Prohibited areaAirspace of defined dimensions identified by an area on the surface of the earth within which the flight of aircraft is prohibited; established for security or other reasons associated with the national welfare.Special use airspace is shown on VFR charts by type and name or number; prohibited, restricted and warning areas are listed in blue in the chart tabulation with altitudes, times of use and controlling agency.Permission from the using or controlling agency (107.45); 73.83: authorization granted by the using agency.Must comply with all airspace restrictions and prohibitions (44809(a)(5)); AC 91-57D 2.2.5.4 names prohibited areas.From the using agency; LAANC does not grant it.14 CFR 73.83; 14 CFR 107.45; 49 U.S.C. 44809(a)(5).
Restricted areaAirspace identified by an area on the surface of the earth within which the flight of aircraft, while not wholly prohibited, is subject to restrictions; restricted areas denote the existence of unusual, often invisible, hazards to aircraft.Shown on VFR charts by type and number; listed in blue in the chart tabulation with altitudes, times of use and controlling agency.Permission from the using or controlling agency (107.45); 73.13: advance permission between the designated altitudes and during the time of designation.Must comply with all airspace restrictions and prohibitions (44809(a)(5)); AC 91-57D 2.2.5.4 names restricted areas.From the using or controlling agency named on the chart; LAANC does not grant it.14 CFR 73.13; 14 CFR 107.45; 49 U.S.C. 44809(a)(5).
Temporary flight restriction (TFR)A Temporary Flight Restriction (TFR) is a type of Notice to Airmen (NOTAM). A TFR defines an area where air travel is restricted due to a hazardous condition, a special event, or a general warning for the entire airspace.Only TFRs relating to national security are charted (broken blue line); all others: check NOTAMs.Must comply with 91.137 to 91.145 and 99.7 (107.47). To fly inside: coordinate with the controlling agency in the TFR, or the Special Governmental Interest (SGI) process (current Part 107 certificate or COA).Must comply with all airspace restrictions and prohibitions (44809(a)(5)); TFRs restrict aircraft, including drones, from operating without permission (FAA TFR page).Controlling agency or SGI; typically only public safety agencies, first responders and media may be eligible; LAANC apps show TFRs but do not authorize flight in them.14 CFR 91.137 to 91.145; 14 CFR 99.7; 14 CFR 107.47; 49 U.S.C. 44809(a)(5).
Washington DC SFRA and FRZA pilot conducting any type of flight operation in the Washington, DC, SFRA/FRZ must comply with the requirements in: 14 CFR section 93.339 (AIM). The DC SFRA includes the DC FRZ (93.335).SFRA symbol for special flight rules areas relating to national security; the FRZ uses the prohibited and restricted area symbology inside the SFRA.Inner 15-mile ring: prohibited without specific FAA authorization (a TSA/FAA waiver and an SGI/COA). Between 15 and 30 miles: permissible in compliance with Part 107, plus 107.41 where the class needs it.Inner 15-mile ring: prohibited without specific FAA authorization. Between 15 and 30 miles: allowed under 44809 and the NOTAM (registered and marked, below 400 ft, visual line of sight, clear weather, never near other aircraft).Inner ring: the FAA access program, for Part 107 and public aircraft operators with justification.14 CFR part 93 subpart V (93.331 to 93.345); 14 CFR 99.7 via the DC NOTAM; 49 U.S.C. 44809.
National security UAS flight restrictions (FAA UAS Data Delivery System map)Drones are prohibited from flying over designated national security sensitive facilities. Operations are prohibited from the ground up to 400 feet above ground level, and apply to all types and purposes of UAS flight operations.Not a sectional chart symbol: shown as red polygons on the FAA UAS Data Delivery System map (AC 91-57D 2.2.5.4).Prohibited; 107.47 requires compliance with 99.7. The FAA does not check 99.7 restrictions when it processes an airspace authorization (UAS Facility Maps FAQ, question 22).Prohibited; 44809(a)(5) requires compliance with all airspace restrictions and prohibitions.No request route stated on the FAA pages read; LAANC does not lift them.14 CFR 99.7; 14 CFR 107.47; 49 U.S.C. 44809(a)(5).
National Security Area (NSA)Pilots are requested to voluntarily avoid flying through the depicted NSA. When it is necessary to provide a greater level of security and safety, flight in NSAs may be temporarily prohibited by regulation under the provisions of 14 CFR section 99.7.Broken magenta line.No authorization; voluntary avoidance unless a 99.7 NOTAM prohibits flight.No authorization; voluntary avoidance unless a 99.7 NOTAM prohibits flight.Check NOTAMs; a temporary prohibition comes by NOTAM.AIM 3-4-8; 14 CFR 99.7 when a NOTAM is issued.

6 kinds of area that are not airspace classes but still limit a drone flight, from the same documents and the FAA's own pages, read November 13, 2026.

Reading airspace on sectional charts and FAA drone maps

For flight planning, use them together: the chart for the class, the facility map for the altitude, and NOTAMs for what changed today.

To understand the airspace at a spot, the FAA Aeronautical Chart Users' Guide (edition effective July 9, 2026) gives the symbols a drone pilot needs most:

  • Class B, C, D

    Solid blue line: Class B. Solid magenta line: Class C. Blue dashed line: Class D.

  • Surface areas

    Magenta dashed line: airspace beginning at the surface designated for airports, and extension areas.

  • Class E floors

    Magenta vignette: Class E from 700 feet AGL. Blue vignette: other floors that abut Class G. Class E exists at 1,200 feet AGL unless designated otherwise.

  • Security

    Broken magenta line: a National Security Area. Broken blue line: a TFR relating to national security, the only kind charted.

  • Special use

    Special use airspace: shown by type and name or number; prohibited, restricted and warning areas are listed in blue in the chart's tabulation with their altitudes, times of use and controlling agency.

The FAA's Detroit sectional chart around Cleveland and Akron.
  • UAS Facility Maps

    The FAA's own maps add what a chart cannot. UAS Facility Map values are altitudes above ground and do not authorize a flight; where a grid reaches past a controlled airspace boundary, the boundary wins.

  • Restrictions

    The FAA's UAS Data Delivery System map shows drone-specific restrictions as red polygons (AC 91-57D), the FAA posts 99.7 restrictions on the same website as the facility maps, and every other TFR is on its NOTAM site.

  • TRSA

    A Terminal Radar Service Area (TRSA) is not an airspace class and is not on the facility maps.

  • B4UFLY

    B4UFLY, offered by FAA-approved companies since February 1, 2024, shows recreational flyers where they can and cannot fly.

Use them together

The chart for the class, the facility map for the altitude, and NOTAMs for what changed today.

Getting LAANC authorization in controlled airspace

LAANC, the FAA's automatic approval in drone apps, gives Part 107 pilots and recreational flyers access to controlled airspace at or below 400 feet, usually in near-real time.

  • Automatic

    Automatic approval is at or below the UAS Facility Map altitude.

    Near-real time
  • Above the map

    Above it, up to 400 feet, only Part 107 pilots may request further coordination, at least 72 hours ahead.

    72 hours
  • No LAANC

    Where LAANC is not offered, the request goes through FAADroneZone and is processed by hand.

    By hand

LAANC, step by step

The steps, the approved apps and what an authorization does not cover are on LAANC: FAA authorization for drone flights.

LAANC guide

Questions about drone airspace classes

What are the classes of airspace in the U.S.?

Class A, B, C, D and E are controlled airspace (14 CFR 1.1) and Class G is uncontrolled (AIM 3-3-1). Prohibited and restricted areas, TFRs and national security areas sit on top of them, and where designations overlap, the more restrictive one applies.

Do I need authorization in Class E airspace?

Only in the surface area designated for an airport, drawn as a magenta dashed line. Class E that starts at 700 or 1,200 feet AGL, the airways and Class E from 14,500 feet MSL need none.

Can I fly at a Class D airport after the tower closes?

It depends on what the Chart Supplement says the area becomes. A Class E surface area still needs an authorization; Class G does not. LAANC apps apply the published schedule.

Can I fly under a Class B shelf?

Under a layer whose floor is above you, you are outside Class B and need no Class B authorization. The airspace below the shelf still decides, so check the class at your spot.

My app shows controlled airspace over my house. Do I need an authorization?

Not always. Controlled airspace includes Class E, which often starts at 700 or 1,200 feet above the ground; a drone below that floor is usually in Class G. You need an authorization only in Class B, C or D or a Class E surface area.

What is a TRSA?

A Terminal Radar Service Area. It is not an airspace class and is not on the UAS Facility Maps, so the class underneath decides whether a drone needs an authorization.

Where is the airspace around an airport listed?

In FAA Order JO 7400.11M, which 14 CFR part 71 incorporates from September 15, 2026 through September 15, 2027. Sectional charts and the UAS Facility Maps show the result.

Sources Named, not linked.

Documents are named, not linked. Each was read on November 13, 2026, and the rules, the FAA pages and the Federal Register that could have moved were read again on November 14, 2026.

Laws and regulations

  • 14 CFR 107.41, Operation in certain airspace, and sections 107.1, 107.45, 107.47, 107.51 and 107.205 (eCFR)
  • 49 U.S.C. 44809, Exception for limited recreational operations of unmanned aircraft, subsection (a)
  • 14 CFR 1.1: controlled airspace; 14 CFR part 71: sections 71.1, 71.31, 71.33, 71.41, 71.51, 71.61 and 71.71
  • 14 CFR 73.13 and 73.83: restricted and prohibited areas; 14 CFR 93.335: the Washington, DC, SFRA; 14 CFR 99.7: special security instructions
  • 36 CFR 1.5: closures in national parks
  • Federal Register, 90 FR 38212 (August 7, 2025): Normalizing Unmanned Aircraft Systems Beyond Visual Line of Sight Operations, proposed rule

FAA manuals and charts

  • Aeronautical Information Manual, chapter 3, sections 1 to 4 (HTML edition effective July 9, 2026)
  • FAA Aeronautical Chart Users' Guide (edition effective July 9, 2026)
  • LAANC USS Performance Rules, version 9.0 (April 18, 2025): the FAA's rules for the suppliers
  • FAA Advisory Circular 91-57D, Exception for Limited Recreational Operations of Unmanned Aircraft (June 24, 2025)
  • Remote Pilot - Small Unmanned Aircraft Systems Airman Certification Standards, FAA-S-ACS-10B (April 2021)

FAA pages

  • FAA fact sheet “Small Unmanned Aircraft Systems (UAS) Regulations (Part 107)” (July 6, 2026)
  • FAA “Recreational Flyers & Community-Based Organizations” (October 29, 2026) and “Flying Near Airports” (April 25, 2024)
  • FAA “UAS Data Exchange (LAANC)” (September 29, 2026), “Part 107 Airspace Authorizations” (October 1, 2026) and “Airspace Authorizations for Recreational Flyers” (May 23, 2023)
  • FAA “UAS Facility Maps” FAQ (June 5, 2025) and “B4UFLY” (August 25, 2026)
  • FAA “Temporary Flight Restrictions” (March 10, 2025), “DC Area Prohibited & Restricted Airspace” (September 16, 2026), “Stadiums and Sporting Events” (November 19, 2025) and “Critical Infrastructure and Public Venues” (February 22, 2023)

Other agencies

  • National Park Service “Uncrewed Aircraft in the National Parks” (May 22, 2025)

Photos: DJI press images. FAA (public domain). Wikimedia Commons: AVA Navigate (CC BY 4.0) and Olga Ernst (CC BY-SA 4.0).